SSIC Thermocouple Protection Tube
Designed to protect thermocouples from extreme temperatures and abrasion.
The SISIC burner nozzles are the best parts for all kinds of kilns which are used gas or oil, especially for the industrial furnace to separate fire as a machine which is be high requested on broad of furnace and different temperature. They can control temperature effectively.
Download PDFIn some special environment, SiC nozzle should be used to produce SiC ceramic products. The products include SiC pipe, SiC ring, roll bar, square beam, burner sleeve, combustion chamber, thermal radiation ceramic inner pipe, cold air pipe, thermocouple protection pipe, sagger, crucible, sandblasting nozzle, desulfurization nozzle, seal, impeller and various high temperature, corrosion resistance, corrosion resistance, etc Wear resistant profiled parts.
How to reduce the occurrence of nozzle failure, the following for everyone to introduce.
Burners are an important part of gas equipment. Evaluating whether the burner design is ideal requires different criteria from different perspectives. Generally, the following aspects can be considered:
The burner meets the heat required for heating or the combustion temperature, and has a certain heat load; (there are many types of gas, mainly natural gas hot gas, liquefied gas, city gas, low calorific value gas, as well as yellow phosphorus tail gas, biogas, etc.).
The burner has certain flame characteristics, such as flame size and shape (flat flame, long flame, short flame), to meet the process requirements.
During the combustion process of the burner, the flame is stable and has certain wind resistance.
The combustion efficiency is high, the gas can be completely burned, and the heat released by the gas can be fully utilized (adjusted by valves such as JGK air-fuel proportional valve).
The burner is equipped with the necessary automatic adjustment and automatic safety devices.
There are very few toxic substances in the flue gas after the burner is burned (full combustion and waste gas treatment).
The burner has a compact structure, is safe and reliable, and has a low cost.
In fact, whether the burner can perform better depends not only on the burner itself, but also by other factors such as air source components and heat exchange equipment. For example, if the heat exchanger is not properly designed or installed, the heat emitted by the burner cannot be fully utilized, resulting in low thermal efficiency. Another example is that the smoke exhaust device is not good, it is difficult to maintain a good combustion state, and the sanitary conditions cannot meet the requirements. Therefore, the performance of the burner must be comprehensively considered in combination with various working conditions to achieve the overall ideal working condition.
Natural gas burners are commonly used combustion devices in industrial kilns. The performance of the natural gas burner will greatly affect the quality of the product. Only reasonable and efficient natural gas burners can meet all the requirements of kiln combustion, heating and product process.
RBSIC / SiSiC silicon carbide burner nozzle is applicable to all kinds of thermal kilns and used in conjunction with burners. It can ensure complete combustion and effectively control the cross section temperature difference of the kiln to make its temperature uniform.
SiSiC spiral nozzle has excellent resistance to acids, especially sulphuric acid and hydrochloric acid, which can be widely used in power plant desulphurisation.
The reaction bonded silicon carbide desulphurisation nozzle is the key component of thermal power plants, large boilers and complete sets of desulphurisation and dust removal equipment. The product has high strength, high hardness, strong corrosion resistance, residual wear resistance, high temperature resistance and other excellent properties, and has an ultra-long service life under harsh conditions.
The spray droplets are evenly distributed, the flow channel is smooth and there is no blockage. At present, there are three series and dozens of varieties of spiral type, vortex type and liquid column type, which have been applied in the desulphurisation and dedusting equipment of many thermal power plants and large boilers.
Spiral nozzle is one of the most characteristic burner nozzles. With the continuous reduction of the spiral, the slurry continuously changes its direction after the tangent and collision of the spiral, and then sprays into a concentric axial cone, and the liquid is not blocked in the channel from entering the nozzle cavity to the outlet. In addition, it still has high absorption efficiency under very low operating pressure and has been widely recognised by the desulphurisation system.
Custom silicon carbide (SiC) burner nozzles offer superior performance in high-temperature applications due to their exceptional durability, thermal stability, and resistance to wear and corrosion.
Silicon carbide (SiC) is a lightweight ceramic material with high strength properties comparable to diamond.
Silicon carbide (SiC) is a synthetic crystalline mineral containing silicon and carbon, generally produced in electrical resistance furnaces at high temperatures of 1700 – 2500 °C.
It has excellent thermal conductivity, low thermal expansion and is resisitance form acids. Silicon carbide ceramic is excellent for applications requiring good erosion and abrasive resistance. Consequently, it is useful in a variety of applications including spray nozzles, shot blast nozzles, ceramic tubing and cyclone components.
A mixture of a carbon material and a silica or quartz sand, it is made to react chemically, resulting in the formation of SiC, which develops as a solid cylindrical ingot around the core, with radial layers ranging from graphite in the inside to α-SiC (the highest-grade material with coarse crystalline structure), β-SiC, metallurgical grade and finally un-reacted material on the outside, which is remelted. SiC can be produced in either black or green, depending on the raw materials used.
Once it is cooled, the SiC ingot is sorted accurately and mainly manually by skilled workers and further processed for different applications. The solid SiC material is then carefully crushed, classified, and milled again if necessary. Another option is to further chemically treat the SiC to obtain specific properties for its applications.
Silicon carbide provides benefits for high-temperature, high-voltage and high-power applications.
These include:
Thanks to its versatile properties, silicon carbide is a widely used ceramic material in many high-temperature and wear-resistant applications in many industries, such as:
We produce sintered SiC tubes, reaction bonded SiC tubes and recrystallized SiC tubes. Our recrystallized SiC products have a high purity, while our reaction bonded and sintered silicon carbide tubes have a high mechanical strength. Our silicon carbide tubes possess good wearability,a low thermal expansion coefficient, extreme corrosion resistance, wear resistance, thermal shock resistance, high hardness and self-lubricating properties.
Silicon carbide (SiC) ceramics have a set of unique physical-chemical properties, such as high hardness and mechanical stability at high temperatures, excellent thermal conductivity and low coefficient of thermal expansion, high resistance to corrosion and oxidation, wide bandgap, and others.
| Item | Recrystallized SiC | Sintered SiC | Reaction Bonded SiC |
|---|---|---|---|
| Purity of Silicon Carbide | 99.5% | 98% | > 88% |
| Max. Working Temp. (`C) | 1650 | 1550 | 1300 |
| Bulk Density (g/cm3) | 2.7 | 3.1 | > 3 |
| Appearance Porosity | < 15% | 2.5 | 0.1 |
| Flexural strength (MPa) | 110 | 400 | 380 |
| Compressive strength (MPa) | > 300 | 2200 | 2100 |
| Thermal expansion (10^-6/`C) | 4.6 (1200℃) | 4.0 (< 500℃) | 4.4 (< 500℃) |
| Thermal conductivity (W/m.K) | 35~36 | 110 | 65 |
| Main characteristics | High temp. High resistance. High purity |
Fracture Toughness | Chemical Resistance |
Reaction Bonded SiC has the lowest cost production technique with a course grain. Reaction Bonded SiC provides somewhat lower hardness and use temperature, but higher thermal conductivity. Reaction bonded silicon carbide has high strength, high hardness, hig abrasion resistance, high temperature resistance, corrosion resistance, good oxidation resistance, good thermal shock resistance, good thermal conductivity, rapid cooling and rapid heat resistance and high temperature creep resistance, etc. It can be made into beam, roller, cooling air pipe, thermocouple protection pipe, temperature measuring pipe, burner nozzle, wear-resisting parts, corrosion-resisting parts, sealing parts and a variety special-shaped structural parts.
Compared with reaction bonded silicon carbide, pressureless sintered silicon carbide has higher purity, better mechanical properties, more prominent corrosion resistance ( Resistantto strong acid and alkali corrosion, It is also the only ceramic material which can resistant to hydrofluoric acid corrosion ), higher wear resistance, because of there’s no free silicon in the material can be used in other materials can not meet the environment, longer service life.
At present, the use of our company’s high wear-resistant ceramic lined steel pipe dozens of thermal power plant practice shows that: ceramic lined steel pipe anti-wear ability, anti-fluid erosion ability.
And it has developed rapidly. When transporting the materials with the harder abrasion (such as ash dregs, slag, coal powder, mining dregs, the rest mines, cement, etc), it will exit the problem that the abrasion of pipes is too rapid. Especially, the abrasion of bent pipes is greatly more rapid.
When transporting the special abrasion materials or erosive materials, it will exit the problem that the damage of pipes is too rapid.
SiC Ceramic lined pipe and the traditional steel pipe, wear-resistant alloy cast steel pipe, cast stone pipe and steel, steel and other rubber pipe is essentially different. Ceramic lined pipe is the outer layer of steel, the inner layer is RBSiC ceramic. Moh’s hardness of up to 13. Wear resistance than carbon steel pipe more than 30 times higher.
In a duct, the elbow wear the fastest, in practice, Ceramic lined pipe used after 1 to 2 years to open the observation and measurement, the composite layer are no obvious wear or tear off, ceramic-coated steel pipe wear Than the thick-walled wear-resistant cast steel pipe increased by nearly 10 times.
Silicon carbide (SiC) is a lightweight ceramic material with high strength properties comparable to diamond. It has excellent thermal conductivity, low thermal expansion, and is resistant to acid corrosion.
Silicon carbide is an excellent ceramic material suitable for applications requiring good corrosion resistance and wear resistance.
Silicon carbide (SiC) ceramics have a set of unique physical-chemical properties, such as high hardness and mechanical stability at high temperatures, excellent thermal conductivity and low coefficient of thermal expansion, high resistance to corrosion and oxidation, wide bandgap, and others.
Sintered Silicon Carbide has demonstrated an excellent performance record as ceramic material in composite armor protection systems. The properties of sintered silicon carbide, such as its high hardness, compressive strength and elastic modulus, provide superior ballistic capability when confronted with high-velocity projectiles. The low specific density of the material makes it suitable in applications where weight requirements are critical.
Sintered Silicon Carbide tubes are used in shell and tube heat exchangers in the chemical process industry. The tubes used in these applications are often over 4 m in length.
Pumps must operate in an infinite variety of demanding environments. Sintered Silicon Carbide offers a high performance seal face material that has proven successful in such diverse pumping applications as chemical processing, refining, mining and pulp and paper processing. The material provides superior corrosion and abrasion resistance; shock resistance; and low sliding friction against a wide range of mating materials.
For state-of-the-art magnetically driven pumps, sintered silicon carbide is particularly suited for thrust and journal bearing components. Excellent corrosion resistance provides optimum performance in many chemical environments. High thermal conductivity minimizes the likelihood of failure due to thermal shock, and its specific strength makes it safe to use at high rotational speeds. Bearing components are usually produced as tight tolerance precision ground parts.
Due to their greater resistance to both wear and thermal shock, sintered silicon carbide seal faces for automotive water pumps are replacing seal faces made of materials such as aluminium oxide. In many cases the material has proven more suitable in meeting the performance demands of U.S. and European vehicles – i.e. lasting the lifetime of the vehicle without leaking. These components are manufactured by conventional high volume pressing and injection moulding methods to meet the economic constraints of the application.
Sintered Silicon Carbide is probably the most popular ceramic alternative to tungsten carbide for blast nozzle applications. Typically providing long life (50% over WC) due to excellent wear and corrosion resistance. The low wear rate maintains the internal nozzle geometry and provides maximum blasting effectiveness, minimum compressor requirements and reduced downtime due to replacement. Sintered silicon carbide is also about one fifth the weight of Tungsten Carbide, so the blasting operation is also easier for the operator. Nozzles are often produced as semi finished (non-ground) components thereby reducing costs.
The outstanding corrosion resistance of sintered silicon carbide, particularly in acids, makes it an ideal candidate for valve and valve trim applications. Typical demanding applications such as slurry flashing, HF acid handling and rare earth processing use sintered silicon carbide valve components.
The excellent corrosion and wear resistance of sintered silicon carbide provides hard surfaces that can be machined to smooth, highly polished finishes. These finishes offer low coefficients of friction and compatibility with forming fabrics. Tiles, inserts and palm guides are available in finished and semi-finished forms.
Often used in applications where tungsten carbide and alumina fail to provide optimum lifetime performance.
The benefit of using silicon carbide for semiconductor components includes; the thermal expansion match to silicon, the resistance to wear and chemical corrosion which leads to reduced maintenance and component recycling. The material is well suited as a structural material for low mass silicon wafer handling components and rigid, dimensionally stable platforms due to its lightness in weight and high elastic modulus. Typical applications include vacuum chucks, chemical mechanical polishing blocks, wafer carriers, and thermocouple protection tubes.
Silicon carbide ceramics are widely used not only in industry, but also in other fields. So, what should be paid attention to when using silicon carbide ceramics?
The hardness of silicon carbide ceramics is very strong, although it does not look as eye-catching as other ceramics, but the use of ornamental ceramics is incomparable. In the process of use, as long as you follow the instructions, there is no need to pay special attention to. Just keep it clean.
If the method used is not correct, the silicon carbide ceramics will be damaged. We can extend its service life by regular maintenance.
Our silicon carbide tube and fitting is carefully handled to minimize damage during storage and transportation and to preserve the quality of our products in their original condition. We guarantee intact during transportation, loading and unloading, and have measures to reduce vibration and impact, so as to ensure the integrity of the product during transportation.
Our Silicon Carbide Tubes (SiC Tubes) are carefully handled to minimize damage during storage and transportation and to preserve the quality of our products in their original condition.
Typical silicon carbide characteristics include:
Typical silicon carbide applications include:
They are used more for operation with wear at low temperature than for high temperature behavior. SiC applications are such as sandblasting injectors, automotive water pump seals, bearings, pump components, and extrusion dies that use high hardness, abrasion resistance, and corrosion resistance of carbide of silicon.
Metallurgy and power industry: The reason why these two industries are put together is mainly because the two industries have a large number of metal pipes for the transmission of coal powder, ash, mud, and the like. After using the wear-resistant elbow pipe, the advantages of strong wear resistance, long life and easy installation are immediately highlighted.
Mining industry: If the wear-resistant elbow pipe is not used, the ordinary pipe is used for the transportation of the ore powder. Due to the filling of the mine and the transportation of the concentrate powder, the wear of the pipe is relatively large, so that the life of these pipes is only about one year. After wearing elbow pipes, the life of such pipes will be extended by a factor of five.
Coal industry: If long-distance wet transport of coal is required, the pipe has the requirements of good wear resistance and high corrosion resistance, and the pipe with wear-resistant elbow can meet these requirements well.
Ceramic lined pipe is made through self-propagating high-temperature synthesis (SHS) technique.
Cast basalt lined steel pipe is composed by lined with cast basalt pipe, outside steel pipe and cement mortar filling between the two layers.
Ceramic tile lined pipes have very uniform coating of specially formulated ceramic material that is affixed to the inner of the pipe.
The material of the rare earth alloy wear-resistant pipe is ZG40CrMnMoNiSiRe, which is also the grade of rare earth alloy steel.
Tubes Erosion Shields are used to protect boiler tubing from the highly erosive effects of high temperatures and pressures thereby greatly extending tube life.
The ASTM A213 T91 seamless tubes are primarily used for boiler, superheater, and heat-exchanger.
